close

CM 420 Offshore

CM 420 Offshore is a pumpable self-levelling underlayment intended for substrates of steel or sheet metal on ships, ferries, oil drilling platforms, etc. Recommended application thickness is 3–30 mm.

Recommended application thickness is 3–30 mm.

Senden Sie alle Dateien

Alle Dateien herunterladen

info

Produktspezifikation

Technische Daten
add_circle
remove_circle

Die Freisetzung von Substanzen corrsive

CT

Druckfestigkeitsklasse

C20

Druckfestigkeit Durchschnitt

35 MPa

Biegezugfestigkeit Klasse

F4

Biegezugfestigkeit Durchschnitt

10 MPa

Feuerwiderstandsklasse

A2fl-s1

RWA

100

RWFC

550

Die Haftung an der Oberfläche

> 1,5 MPa

Dicke 1

3–30 mm

Körnung

< 0.5 mm

Materialverbrauch

1.1 kg/m²/mm

Gewicht (trocken)

1100 kg/m³

Wasserbedarf

4,3 l/15 kg

Fließrate

max 145 mm

Betriebstemperatur

10–25 °C

Mischzeit

3 min

Arbeitszeit

approx. 60 min

Abbindezeit

> 4 hrs

Abdeckbar (Fliesen)

24 hrs

Carpetable

1–3 days

pH-Wert

approx. 11

Wasserschaden resistent

yes

Oberflächen Zu, 28 Tage (poliert, geladene Oberfläche)

> 1,5 MPa

Schwindung

0.04–0.06 %

TVOC 28 Tage

30 μg/m² h

Verpackung
add_circle
remove_circle

42005

15 kg

info

Benutzen

Vorbehandlung
add_circle
remove_circle

The substrate should be clean and free of dust, cement skin, grease and other impurities that can prevent adhesion. Adhesion and surface resistance of the substrate should be no less than 0.5 MPa. Always prime the underlying substrate with PP600 and allow to dry before pouring. In terms of the primer forming a film, the temperature of the substrate must not fall below 10 °C. For best results, the ambient temperature in the work area should be between 10 and 25 °C.

Vermischung
add_circle
remove_circle

Mix CM 420 Offshore with max 4.3 liters of water (max 29 %) per 15 kg bag. Create the mixture with a drilling machine and a whisk, or a mixing pump intended for this purpose. The correct water mixture can be tested using a slump test with a cylinder with Ø 30 mm and a height of 50 mm on a 300 x 300 mm plexiglas plate. With the correct water mixture, the spread should be max 145 mm. The slump test also checks that the material is well blended and that there is no separation.

Anwendung
add_circle
remove_circle

The mixed material is applied by hand, or pumped out onto the substrate in lengths and leveled with a toothed smoother. Each new ribbon is added to the old one as soon as possible so that the material can blend together and create an even surface. The width of the ribbons can be adjusted to the capacity of thwe mixing pump and the thickness of the covering. Use the Combimix form foam for edging. In order to avoid drainage pipes from getting clogged, always make sure the drains are properly sealed before pouring.

Nachbehandlung und Härten
add_circle
remove_circle

You can easily shape or cut the semi-hardened self-leveling underlayment material before it fully dries. Always make sure that the material is sufficiently dry before installing flooring. The drying time is 1–3 days for the product to be carpetable. The guiding value assumes a curing temperature of approximately 20 °C, 40 % RH and proper air flow. Newly produced surfaces must be protected against wind, sun and rain.

Verbrauchsrechner

CM 420 Offshore

Verbrauchsrechner

phone

+46 171 46 65 90

Kontaktieren Sie unsere Auftragsabteilung

Kontaktiere uns

  • Verkstadsvägen 6
  • 746 40 Bålsta, Schweden
  • Tel. +46 171 46 65 90
  • E-mail: [email protected]

Combimix

Combimix entwickelt und produziert Mineral-basierte Produkte für die Bauindustrie. Unsere Produktpalette umfasst Produkte für den Bodenausgleich, Fassadenputz, Rendering, Beton-Resurfacing und Restaurierungsmörtel für Kulturbauten. Wir führen Vertrieb in Schweden, Dänemark, Norwegen und den Vereinigten Staaten.

Produktkategorien