search
close

CM 100 Gypsos

Combimix CM 100 Gypsos is a pumpable, gypsum based self-levelling underlayment. The product is suitable for new construction and renovation.

The product is intended for indoor use on substrates of concrete, lightweight concrete, stone, ceramic tiles gypsum underlay, wood and homogenous PVC. The product is intended to be covered with a top layer, e.g. tiles, carpets or similar.

Send all files

Download all files

info

Product specification

Technical data
add_circle
remove_circle

Compressive strength class

3,100 psi

Flexural Strength, class

725 psi

Fire resistance class

A1fl

Adhesion to surface

> 217 psi

Thickness 1

1/4”–2”

Weight (dry state)

111 lbs/ft³

Wet volume weight

120 lbs/ft³

Water requirements

4.0 qt/44 lb

Flow rate

max 5 1/2”

Workplace temperature

50–77 °F

Mixing time

3 min

Working time

10–20 min

Final set

1–3 hrs

Coverable (tiles)

12 hrs

pH

approx. 11

Water damage resistant

yes

Shrinkage

0–0,01 %

TVOC 28 days

< 10 μg/(m² h)

Packaging
add_circle
remove_circle

80005

20 kg

80003

1000 kg

info

Use

Pre-treatment
add_circle
remove_circle

The substrate should be clean and free of dust, cement skin, grease and other impurities that can prevent adhesion. Adhesion and surface resistance of the substrate should be no less than 72 psi. If the substrate is weaker than 72 psi, a test should be executed. The test should be applied on 1.6x10.0 ft and evaluated after 3 days for any cracks. Contact Combimix for consultation. Always prime the substrate with PP 600 and allow to dry before pouring (see PP 600 datasheet for proper dilution and installation directions). In terms of the primer forming a film, the temperature of the substrate must not be below 50 °F. For best results, the ambient temperature in the work area should be between 50 and 77 °F. At higher or lower temperatures, the time for curing will shorten or extend. Protect the product from excessive heat, excessive cold and draft conditions during and after the installation. It is recommended that the installation should be done with a proper air ventilation from an HVAC system. With the risk for cracks due to shrinkage or settings in the subfloor, a concrete surface should not be leveled within the first 28 days after casting. As a recommendation the RH in the concrete should have reached RH 90 % as the upper limit for pouring the CM 100. Use the Combimix form foam for edging. In order to avoid drainage pipes from getting clogged, always make sure the drains are properly sealed before pouring.

Mixing
add_circle
remove_circle

Mix the dry powder with max 4.0 qt (3.8 L) of water, max 19 %, per 44 lb (20 kg) bag. Manual mix: Mix with a heavy duty ½” (13 mm), 650 rpm minimum drill and a whisk to obtain a lump free consistency. Mixing pump: Mixing pump intended for this purpose. Start pump at minimum of 125 gallons of water per hour and adjust as necessary to yield a self-leveling consistency. Please note that the production capacity and speed of the pump will dictate the gallons of water ratio per hour. The Combimix slump test must always be carried out to ensure the product performance and that the mixture is homogenized and free from separation. The correct water mixture can be tested using a slump test with a cylinder with Ø 1.18” and a height of 1.97” (Ø 30 mm and a height of 50 mm) on 11.8” x 11.8” (300 x 300 mm) plexiglas plate. With the correct water mixture, the spread should be max 5 1/2” (140 mm) for application thickness 1/8”–1 1/4” (3–30 mm). The slump test also checks that the material is well blended and that there is no separation.

Application
add_circle
remove_circle

The mixed material is applied by hand, or pumped onto the substrate in lengths. Each new ribbon is added to the old one as soon as possible so that the material can blend together and create an even surface. The width of the ribbons can be adjusted to the capacity of the mixing pump and the thickness of the covering. The material requires a light treatment with a toothed trowel to provide maximum smoothness. Working time of the product is apx. 10 to 20 minutes. Application thickness 1/4”–2” (5–50 mm).

Post-treatment and curing
add_circle
remove_circle

You can easily shape or cut the semi hardened self-leveling underlayment material before it fully dries. Protect the surface for up to 24 hours after installation. Material can be walked on after 1–3 hours. Always make sure that the material is sufficiently dry before it will be covered. The guided time for dehydration down to RH 85 % of the product is 0.39” (10 mm) per week. The guiding value assumes a curing temperature of approximately 68 °F, 40 % RH and proper air flow.

Consumption calculator

CM 100 Gypsos

Consumption calculator

phone

+46 171 46 65 90

Call our order department

Contact us

  • Verkstadsvägen 6
  • 746 40 Bålsta, Sweden
  • Tel. +46 171 46 65 91
  • Fax. +46 171 46 65 99
  • E-mail: info@combimix.com

Combimix

Combimix develops and manufactures mineral-based products for the construction industry. Our product range includes products for floor levelling, façade plastering, rendering, concrete resurfacing and restoration mortar for cultural buildings. We conduct sales in Europe and USA.

Product categories