search
close

CM 760 Fibre

CM 760 Fibre is a pumpable, fibre-reinforced self-levelling underlayment.

The product is fibre reinforced, quick setting, self-drying and has a very good flow rate. The CM 760 is suitable for new construction, renovation and heated floor systems. The product is intended for indoor use on substrates of concrete, lightweight concrete, stone, ceramic tiles, homogenous PVC, wood and gypsum underlay. CM 760 is frost resistant and can be used outdoor on concrete substrates, under teils, except in salt environments.

Send all files

Download all files

info

Product specification

Technical data
add_circle
remove_circle

Release of corrsive substances

CT

Compressive strength class

C30

Compressive strength average

35 MPa

Flexural strength class

F7

Flexural strength average

8 MPa

Fire resistance class

A1fl

RWFC

550

Adhesion to surface

B1.5

Thickness 1

5–50 mm

Thickness 2

6–20 mm on lightweight concrete

Grain size

< 2 mm

Material consumption

1,7 kg/m²/mm

Weight (dry state)

1700 kg/m³

Water requirements

3,6 l/20 kg

Flow rate

max 135 mm

Workplace temperature

10–25 °C

Mixing time

3 min

Working time

10–25 min

Final set

1–3 hrs

Coverable (tiles)

12 hrs

Carpetable

1–3 days

pH

approx. 11

Water damage resistant

Yes

Surface Tensile Bond Strength, 28 days (sanded, loaded surface)

> 1.5 MPa

Shrinkage

0.03–0.05 %

TVOC 28 days

10 μg/(m2 h)

Packaging
add_circle
remove_circle

76005

20 kg

info

Use

Pre-treatment
add_circle
remove_circle

The substrate should be clean and free of dust, cement skin, grease and other impurities that can prevent adhesion. Adhesion and surface strength of the substrate should be no less than 0.5 MPa. Always prime the underlying substrate with PP 600 and allow to dry before pouring. In terms of the primer forming a film, the temperature of the substrate must not fall below 10 °C. For best results, the ambient temperature in the work area should be between 10 and 25 °C. At higher or lower temperatures, the time for curing will shorten or extend. With the risk for cracks due to shrinkage or settings in the subfloor, a concrete surface should not be leveled within the first 28 days after casting. As a recommendation the RH in the concrete should have reached RH 90 % as the upper limit for pouring the CM 760. Use the Combimix form foam for edging. In order to avoid drainage pipes from getting clogged, always make sure the drains are properly sealed before pouring.

Mixing
add_circle
remove_circle

Mix the dry powder with max 3.6 liters of water (max 18 %) per 20 kg bag. Mix with a drilling machine and a whisk, or a mixing pump intended for this purpose. The correct water mixture can be tested using a slump test with a cylinder with Ø 30 mm and a height of 50 mm on 300 x 300 mm plexiglas plate. With the correct water mixture, the spread should be max 135 mm. The slump test also checks that the material is well blended and that there is no separation.

Application
add_circle
remove_circle

The mixed material is applied by hand, or pumped out onto the substrate in lengths. Each new ribbon is added to the old one as soon as possible so that the material can blend together and create an even surface. The width of the ribbons can be adjusted to the capacity of the mixing pump and the thickness of the covering. The material requires a light treatment with a toothed trowel to provide maximum smoothness.

Post-treatment and curing
add_circle
remove_circle

You can easily shape or cut the semi- hardened self-leveling underlayment material before it fully dries. Always make sure that the material is sufficiently dry before it will be covered by a carpet or a foilsystem. The CM 760 may be covered by a carpet or a foilsystem after 1-3 days depending on the thickness. The guiding value assumes a curing temperature of approximately 20 °C, 40 % RH and proper air flow.

Consumption calculator

CM 760 Fibre

Consumption calculator

phone

+46 20 21 21 00

Call our order department

Contact us

  • Verkstadsvägen 6
  • 746 40 Bålsta, Sweden
  • Tel. +46 171 46 65 90
  • Fax. +46 171 46 65 99
  • E-mail: info@combimix.com

Combimix

Combimix develops and manufactures mineral-based products for the construction industry. Our product range includes products for floor levelling, façade plastering, rendering, concrete resurfacing and restoration mortar for cultural buildings. We conduct sales in Europe and USA.

Product categories