search
close

CM 840 Fine

CM 840 is a multipurpose trowelable patching compound for underlayments.

CM 840 can be installed on all types of concrete, well-bonded gypsum, bonded ceramic tile, quarry tile, Vinyl (non-cushion backed), VAT, VCT and PVC. Use Primer to block contact with gypsum-based surfaces. CM 840 is perfect for repairing cracks or creating slopes to drains. It may also be used on walls for repairs.

Stuur alle bestanden

Download alle bestanden

info

Productspecificatie

Technische data
add_circle
remove_circle

Vrijgave van corrsive stoffen

CT

Druksterkteklasse

C25

Druksterkte gemiddelde

32 MPa

Buigsterkte klasse

F7

Buigsterkte gemiddelde

7 MPa

Brandwerendheidsklasse

A1

Hechting aan oppervlakte

> 1 MPA

Dikte 1

0–50 mm

Dikte 2

6–20 mm

Korrelgrootte

< 0.5 mm

Materiaalverbruik

1.7 kg/m²/mm

Gewicht (droge toestand)

1700 kg/m³

Water behoeften

4,2 l/15 kg

Bedrijfstemperatuur

10–25 °C

Mengtijd

2+1 min

Werktijd

20–30 min

Final set

30–60 min

Bedekbaar (tegels)

1 hr

Carpetable

1–3 hrs

pH

approx. 11

Waterschade resistant

yes

Oppervlakte hechtsterkte, 28 dagen (gepolijst, geladen oppervlak)

> 1 MPa

Inkrimping

0.03–0.05 %

Verpakking
add_circle
remove_circle

84007

15 kg

info

Gebruik

Pre-behandeling
add_circle
remove_circle

The substrate should be clean and free of dust, cement skin, grease and other impurities that may prevent adhesion. Adhesion and surface resistance of the substrate should be no less than 0,5 MPa. Always prime the substrate with PP 600 and allow to dry before pouring (see PP 600 datasheet for proper dilution and installation directions). In terms of the primer forming a film, the temperature of the substrate must not be below 10 °C. For best results, the ambient temperature in the work area should be between 10-25 °C. At higher or lower temperatures, the time for curing will shorten or extend. Protect the product from excessive heat, excessive cold and draft conditions during and after the installation. It is recommended that the installation should be done with a proper air ventilation from an HVAC system. With the risk for cracks due to shrinkage or settings in the subfloor, a concrete surface should not be leveled within the first 28 days after casting. As a recommendation the RH in the concrete should have reached RH 90 % as the upper limit for applying the CM 840.

Menging
add_circle
remove_circle

Mix the dry powder with max 4.2 L of cold, potable water, max 28 %, per 15 kg bag. Do not overwater. Mix for 2 minutes with a heavy duty drill mixer (650 minimum rpm) to obtain a lump-free mix.Let the mixed CM 840 rest for 1 minute and then mix it for 1 minute again. Product may be refreshed by re-mixing but do not ad more water.

Toepassing
add_circle
remove_circle

Apply blended material onto substrate at a thickness of 0–50 mm for all surfaces by using a steel trowel. After initial set of material (approx. 10–15 min.), remove any overlap marks, seams and inconsistencies by scraping with a steel trowel.

Post -behandeling en uitharden
add_circle
remove_circle

Protect CM 840 from excessive heat or draft conditions during the curing process. Protect for up to 24 hours after completed installation. Material can be walked on after 30–45 minutes. Before covered by carpet be sure that the subfloor is dry enough. CM 840 is coverable after 1-3 hours. The guiding value assumes a curing temperature of approximately 20 °C, 40 % RH and proper air flow.

Verbruikscalculator

CM 840 Fine

Verbruikscalculator

phone

+46 171 46 65 90

Bel onze bestelling afdeling

Neem contact met ons op

  • Verkstadsvägen 6
  • 746 40 Bålsta, Zweden
  • Tel. +46 171 46 65 90
  • Fax. +46 171 46 65 99
  • E-mail: info@combimix.com

Combimix

Combimix ontwikkelt en produceert minerale producten voor de bouw. Ons assortiment omvat producten voor vloer egalisatie, gevelbepleistering, rendering, beton resurfacing en restauratie mortel voor culturele gebouwen. We verkopen in Zweden, Denemarken, Noorwegen en de Verenigde Staten.

Productcategorieën