search
close

CM 900 Industrial Base

CM 900 Industrial Base is a pumpable self-levelling underlayment.

The product is intended for indoor use on substrates of concrete. CM 900 is used as a build-up and sublayer to CM 920, CM 920 Design, CM 940 or CM 960.

Stuur alle bestanden

Download alle bestanden

info

Productspecificatie

Technische data
add_circle
remove_circle

Vrijgave van corrsive stoffen

CT

Druksterkteklasse

C25

Druksterkte gemiddelde

35 MPa

Buigsterkte klasse

F5

Buigsterkte gemiddelde

7 MPa

Brandwerendheidsklasse

A1fl

Hechting aan oppervlakte

B1.5

Dikte 1

5–50 mm

Korrelgrootte

< 2 mm

Materiaalverbruik

1.7 kg/m²/mm

Gewicht (droge toestand)

1700 kg/m³

Water behoeften

3,4 l/20 kg

Debiet

max 125 mm

Bedrijfstemperatuur

10–25 °C

Mengtijd

3 min

Werktijd

15–25 min

Final set

1–3 hrs

pH

approx. 11

Waterschade resistant

yes

Oppervlakte hechtsterkte, 28 dagen (gepolijst, geladen oppervlak)

> 1.5 MPa

Inkrimping

0.03–0.05 %

Verpakking
add_circle
remove_circle

90005

20 kg

info

Gebruik

Pre-behandeling
add_circle
remove_circle

The substrate should be clean and free of dust, cement skin, grease and other impurities that can prevent adhesion. Adhesion and surface resistance of the substrate should be no less than 1.5 MPa. Always prime the underlying substrate with PP 600 and allow to dry before pouring. In terms of the primer forming a film, the temperature of the substrate must not fall below 10 °C. For best results, the ambient temperature in the work area should be between 10 and 25 °C. At higher or lower temperatures, the time for curing will shorten or extend. With the risk for cracks due to shrinkage or settings in the subfloor, a concrete surface should not be leveled within the first 28 days after casting. As a recommendation the RH in the concrete should have reached RH 90 % as the upper limit for pouring the CM 900. Use the Combimix form foam for edging. In order to avoid drainage pipes from getting clogged, always make sure that the drains are properly sealed before pouring.

Menging
add_circle
remove_circle

Mix the dry powder with max 3.4 liters of water (max 17 %) per 20 kg bag. Mix with a drilling machine and a whisk, or a mixing pump intended for this purpose. The correct water mixture can be tested using a slump test with a cylinder with Ø 30 mm and a height of 50 mm on a 300 x 300 mm plexiglas plate. With the correct water mixture, the spread should be max 125 mm. The slump test also checks that the material is well blended and that there is no separation.

Toepassing
add_circle
remove_circle

The mixed material is applied by hand, or pumped out onto the substrate in lengths. Each new ribbon is added to the old one as soon as possible so that the material can blend together and create an even surface. The width of the ribbons can be adjusted to the capacity of the mixing pump and the thickness of the covering. The material requires a light treatment with a toothed trowel to provide maximum smoothness.

Post -behandeling en uitharden
add_circle
remove_circle

You can easily shape or cut the semi-hardened self-leveling underlayment material before it fully dries. CM 900 shall always be coated with a toplayer of CM 920, CM 920 Design, CM 940 or CM 960. The product shall not be coated with epoxy or PU directly.

Verbruikscalculator

CM 900 Industrial Base

Verbruikscalculator

phone

+46 20 21 21 00

Bel onze bestelling afdeling

Neem contact met ons op

  • Verkstadsvägen 6
  • 746 40 Bålsta, Zweden
  • Tel. +46 171 46 65 90
  • Fax. +46 171 46 65 99
  • E-mail: info@combimix.com

Combimix

Combimix ontwikkelt en produceert minerale producten voor de bouw. Ons assortiment omvat producten voor vloer egalisatie, gevelbepleistering, rendering, beton resurfacing en restauratie mortel voor culturele gebouwen. We verkopen in Zweden, Denemarken, Noorwegen en de Verenigde Staten.

Productcategorieën